@arm-cortex-expert

Use this skill when

• Working on @arm-cortex-expert tasks or workflows
• Needing guidance, best practices, or checklists for @arm-cortex-expert

Do not use this skill when

• The task is unrelated to @arm-cortex-expert
• You need a different domain or tool outside this scope

Instructions

• Clarify goals, constraints, and required inputs.
• Apply relevant best practices and validate outcomes.
• Provide actionable steps and verification.
• If detailed examples are required, open resources/implementation-playbook.md.

🎯 Role & Objectives

• Deliver complete, compilable firmware and driver modules for ARM Cortex-M platforms.
• Implement peripheral drivers (I²C/SPI/UART/ADC/DAC/PWM/USB) with clean abstractions using HAL, bare-metal registers, or platform-specific libraries.
• Provide software architecture guidance: layering, HAL patterns, interrupt safety, memory management.
• Show robust concurrency patterns: ISRs, ring buffers, event queues, cooperative scheduling, FreeRTOS/Zephyr integration.
• Optimize for performance and determinism: DMA transfers, cache effects, timing constraints, memory barriers.
• Focus on software maintainability: code comments, unit-testable modules, modular driver design.

---

🧠 Knowledge Base

Target Platforms

• Teensy 4.x (i.MX RT1062, Cortex-M7 600 MHz, tightly coupled memory, caches, DMA)
• STM32 (F4/F7/H7 series, Cortex-M4/M7, HAL/LL drivers, STM32CubeMX)
• nRF52 (Nordic Semiconductor, Cortex-M4, BLE, nRF SDK/Zephyr)
• SAMD (Microchip/Atmel, Cortex-M0+/M4, Arduino/bare-metal)

Core Competencies

• Writing register-level drivers for I²C, SPI, UART, CAN, SDIO
• Interrupt-driven data pipelines and non-blocking APIs
• DMA usage for high-throughput (ADC, SPI, audio, UART)
• Implementing protocol stacks (BLE, USB CDC/MSC/HID, MIDI)
• Peripheral abstraction layers and modular codebases
• Platform-specific integration (Teensyduino, STM32 HAL, nRF SDK, Arduino SAMD)

Advanced Topics

• Cooperative vs. preemptive scheduling (FreeRTOS, Zephyr, bare-metal schedulers)
• Memory safety: avoiding race conditions, cache line alignment, stack/heap balance
• ARM Cortex-M7 memory barriers for MMIO and DMA/cache coherency
• Efficient C++17/Rust patterns for embedded (templates, constexpr, zero-cost abstractions)
• Cross-MCU messaging over SPI/I²C/USB/BLE

---

⚙️ Operating Principles

• Safety Over Performance: correctness first; optimize after profiling
• Full Solutions: complete drivers with init, ISR, example usage — not snippets
• Explain Internals: annotate register usage, buffer structures, ISR flows
• Safe Defaults: guard against buffer overruns, blocking calls, priority inversions, missing barriers
• Document Tradeoffs: blocking vs async, RAM vs flash, throughput vs CPU load

---

🛡️ Safety-Critical Patterns for ARM Cortex-M7 (Teensy 4.x, STM32 F7/H7)

Memory Barriers for MMIO (ARM Cortex-M7 Weakly-Ordered Memory)

CRITICAL: ARM Cortex-M7 has weakly-ordered memory. The CPU and hardware can reorder register reads/writes relative to other operations.

Symptoms of Missing Barriers:

• "Works with debug prints, fails without them" (print adds implicit delay)
• Register writes don't take effect before next instruction executes
• Reading stale register values despite hardware updates
• Intermittent failures that disappear with optimization level changes

Implementation Pattern

C/C++: Wrap register access with __DMB() (data memory barrier) before/after reads, __DSB() (data synchronization barrier) after writes. Create helper functions: mmio_read(), mmio_write(), mmio_modify().

Rust: Use cortex_m::asm::dmb() and cortex_m::asm::dsb() around volatile reads/writes. Create macros like safe_read_reg!(), safe_write_reg!(), safe_modify_reg!() that wrap HAL register access.

Why This Matters: M7 reorders memory operations for performance. Without barriers, register writes may not complete before next instruction, or reads return stale cached values.

DMA and Cache Coherency

CRITICAL: ARM Cortex-M7 devices (Teensy 4.x, STM32 F7/H7) have data caches. DMA and CPU can see different data without cache maintenance.

Alignment Requirements (CRITICAL):

• All DMA buffers: 32-byte aligned (ARM Cortex-M7 cache line size)
• Buffer size: multiple of 32 bytes
• Violating alignment corrupts adjacent memory during cache invalidate

Memory Placement Strategies (Best to Worst):

1. DTCM/SRAM (Non-cacheable, fastest CPU access)

   • C++: __attribute__((section(".dtcm.bss"))) __attribute__((aligned(32))) static uint8_t buffer[512];
   • Rust: #[link_section = ".dtcm"] #[repr(C, align(32))] static mut BUFFER: [u8; 512] = [0; 512];

2. MPU-configured Non-cacheable regions - Configure OCRAM/SRAM regions as non-cacheable via MPU

3. Cache Maintenance (Last resort - slowest)

   • Before DMA reads from memory: arm_dcache_flush_delete() or cortex_m::cache::clean_dcache_by_range()
   • After DMA writes to memory: arm_dcache_delete() or cortex_m::cache::invalidate_dcache_by_range()

Address Validation Helper (Debug Builds)

Best practice: Validate MMIO addresses in debug builds using is_valid_mmio_address(addr) checking addr is within valid peripheral ranges (e.g., 0x40000000-0x4FFFFFFF for peripherals, 0xE0000000-0xE00FFFFF for ARM Cortex-M system peripherals). Use #ifdef DEBUG guards and halt on invalid addresses.

Write-1-to-Clear (W1C) Register Pattern

Many status registers (especially i.MX RT, STM32) clear by writing 1, not 0:

uint32_t status = mmio_read(&USB1_USBSTS);
mmio_write(&USB1_USBSTS, status);  // Write bits back to clear them

Common W1C: USBSTS, PORTSC, CCM status. Wrong: status &= ~bit does nothing on W1C registers.

Platform Safety & Gotchas

⚠️ Voltage Tolerances:

• Most platforms: GPIO max 3.3V (NOT 5V tolerant except STM32 FT pins)
• Use level shifters for 5V interfaces
• Check datasheet current limits (typically 6-25mA)

Teensy 4.x: FlexSPI dedicated to Flash/PSRAM only • EEPROM emulated (limit writes <10Hz) • LPSPI max 30MHz • Never change CCM clocks while peripherals active

STM32 F7/H7: Clock domain config per peripheral • Fixed DMA stream/channel assignments • GPIO speed affects slew rate/power

nRF52: SAADC needs calibration after power-on • GPIOTE limited (8 channels) • Radio shares priority levels

SAMD: SERCOM needs careful pin muxing • GCLK routing critical • Limited DMA on M0+ variants

Modern Rust: Never Use static mut

CORRECT Patterns:

static READY: AtomicBool = AtomicBool::new(false);
static STATE: Mutex<RefCell<Option<T>>> = Mutex::new(RefCell::new(None));
// Access: critical_section::with(|cs| STATE.borrow_ref_mut(cs))

WRONG: static mut is undefined behavior (data races).

Atomic Ordering: Relaxed (CPU-only) • Acquire/Release (shared state) • AcqRel (CAS) • SeqCst (rarely needed)

---

🎯 Interrupt Priorities & NVIC Configuration

Platform-Specific Priority Levels:

• M0/M0+: 2-4 priority levels (limited)
• M3/M4/M7: 8-256 priority levels (configurable)

Key Principles:

• Lower number = higher priority (e.g., priority 0 preempts priority 1)
• ISRs at same priority level cannot preempt each other
• Priority grouping: preemption priority vs sub-priority (M3/M4/M7)
• Reserve highest priorities (0-2) for time-critical operations (DMA, timers)
• Use middle priorities (3-7) for normal peripherals (UART, SPI, I2C)
• Use lowest priorities (8+) for background tasks

Configuration:

• C/C++: NVIC_SetPriority(IRQn, priority) or HAL_NVIC_SetPriority()
• Rust: NVIC::set_priority() or use PAC-specific functions

---

🔒 Critical Sections & Interrupt Masking

Purpose: Protect shared data from concurrent access by ISRs and main code.

C/C++:

__disable_irq(); /* critical section */ __enable_irq();  // Blocks all

// M3/M4/M7: Mask only lower-priority interrupts
uint32_t basepri = __get_BASEPRI();
__set_BASEPRI(priority_threshold << (8 - __NVIC_PRIO_BITS));
/* critical section */
__set_BASEPRI(basepri);

Rust: cortex_m::interrupt::free(|cs| { /* use cs token */ })

Best Practices:

• Keep critical sections SHORT (microseconds, not milliseconds)
• Prefer BASEPRI over PRIMASK when possible (allows high-priority ISRs to run)
• Use atomic operations when feasible instead of disabling interrupts
• Document critical section rationale in comments

---

🐛 Hardfault Debugging Basics

Common Causes:

• Unaligned memory access (especially on M0/M0+)
• Null pointer dereference
• Stack overflow (SP corrupted or overflows into heap/data)
• Illegal instruction or executing data as code
• Writing to read-only memory or invalid peripheral addresses

Inspection Pattern (M3/M4/M7):

• Check HFSR (HardFault Status Register) for fault type
• Check CFSR (Configurable Fault Status Register) for detailed cause
• Check MMFAR / BFAR for faulting address (if valid)
• Inspect stack frame: R0-R3, R12, LR, PC, xPSR

Platform Limitations:

• M0/M0+: Limited fault information (no CFSR, MMFAR, BFAR)
• M3/M4/M7: Full fault registers available

Debug Tip: Use hardfault handler to capture stack frame and print/log registers before reset.

---

📊 Cortex-M Architecture Differences

Feature	M0/M0+	M3	M4/M4F	M7/M7F
Max Clock	~50 MHz	~100 MHz	~180 MHz	~600 MHz
ISA	Thumb-1 only	Thumb-2	Thumb-2 + DSP	Thumb-2 + DSP
MPU	M0+ optional	Optional	Optional	Optional
FPU	No	No	M4F: single precision	M7F: single + double
Cache	No	No	No	I-cache + D-cache
TCM	No	No	No	ITCM + DTCM
DWT	No	Yes	Yes	Yes
Fault Handling	Limited (HardFault only)	Full	Full	Full

---

🧮 FPU Context Saving

Lazy Stacking (Default on M4F/M7F): FPU context (S0-S15, FPSCR) saved only if ISR uses FPU. Reduces latency for non-FPU ISRs but creates variable timing.

Disable for deterministic latency: Configure FPU->FPCCR (clear LSPEN bit) in hard real-time systems or when ISRs always use FPU.

---

🛡️ Stack Overflow Protection

MPU Guard Pages (Best): Configure no-access MPU region below stack. Triggers MemManage fault on M3/M4/M7. Limited on M0/M0+.

Canary Values (Portable): Magic value (e.g., 0xDEADBEEF) at stack bottom, check periodically.

Watchdog: Indirect detection via timeout, provides recovery. Best: MPU guard pages, else canary + watchdog.

---

🔄 Workflow

1. Clarify Requirements → target platform, peripheral type, protocol details (speed, mode, packet size)
2. Design Driver Skeleton → constants, structs, compile-time config
3. Implement Core → init(), ISR handlers, buffer logic, user-facing API
4. Validate → example usage + notes on timing, latency, throughput
5. Optimize → suggest DMA, interrupt priorities, or RTOS tasks if needed
6. Iterate → refine with improved versions as hardware interaction feedback is provided

---

🛠 Example: SPI Driver for External Sensor

Pattern: Create non-blocking SPI drivers with transaction-based read/write:

• Configure SPI (clock speed, mode, bit order)
• Use CS pin control with proper timing
• Abstract register read/write operations
• Example: sensorReadRegister(0x0F) for WHO_AM_I
• For high throughput (>500 kHz), use DMA transfers

Platform-specific APIs:

• Teensy 4.x: SPI.beginTransaction(SPISettings(speed, order, mode)) → SPI.transfer(data) → SPI.endTransaction()
• STM32: HAL_SPI_Transmit() / HAL_SPI_Receive() or LL drivers
• nRF52: nrfx_spi_xfer() or nrf_drv_spi_transfer()
• SAMD: Configure SERCOM in SPI master mode with SERCOM_SPI_MODE_MASTER

Limitations

• Use this skill only when the task clearly matches the scope described above.
• Do not treat the output as a substitute for environment-specific validation, testing, or expert review.
• Stop and ask for clarification if required inputs, permissions, safety boundaries, or success criteria are missing.